Відео

I am doing this at my job currently, and no one including myself. Have ever run this machine. Had someone in the past. I can not figure out how to get the laser to the center. So it's easy for me to find the center to line up. It keeps putting it in the bottom corner and then framing a square. How do I get it to find the center of the logo so I can center it before I hit start? Framing, it does nothing when I'm doing a bunch of different names that are all not the exact same length.

Running a bit hot...I can smell it

this video was terrible, for a - how to engrave TITLE

I have a JL5Kentok tool laser and it says that it’s not compatible with windows 10 an older version of windows

yeah downloaded the file, sadly i couldnt open it to extract the files.

Wow!

I want to this macthine

How do they feel when you throw them down and play? I recently made some resin and they were much too lightweight. What kind of wood do you typically use fir this item

Como mejorar el trazado de la imagen después de vectorizar ?

I just had xtool d1 pro 20 W and I wasn’t happy with it. Now I’m saving up and I was thinking about doing the XT P2, which is pretty classy and allows for up to 9 feet of engraving material passed through it. Does this machine offer the same thing to threw the software, does it have rollers to let the material go through it and roll along to create a large piece or is does it just allow for the material to sit there for the workspace available to it?

What is the source of the laser? I understand it's not CO2

On my wish list

San po location nyu

power percentage?

so in other words laser printing

Thanks

Any pricing range. Let's say one you used in video?

are these in stock???

But what laser

Light trip hone ke bad machine ko vahin se kaise chalayen

How do I get rid of the lines ? Everytime I do a picture there are lines

Very nice, how much lol

Will any new/updated set up tutorials be made? I tried using this tutorial for a recently purchased LS 2440 and it’s very confusing…

HI, i have a Oculus quest 2 using oculink with a 5V DC 10W cable. how can I increase my PC's USB OUTPUT power as it is not providing the needed 10W

The bloopers 😂😂😂

Thank you, this is the one I was looking for. So it is Handle --> Bitmap Handle --> Get outline

Can you eat it?

How many LPI or what was your line spacing?

Settings?

That was satisfying😀

What lens??

What’s an optimal light and velocity

Hi there, would be nice to get a video of how to properly screw on the lense housing. I'm confused about the the screw that squeezes the spring. Does that have to be all the way down? Or just enough. Trying to understand how the auto focus works. Is it sending a signal to the material to see how far away the material is. Or is it sending a horizontal sense to the nozzle as it touches the material and raises up. I have a feeling the position of the spring tightening screw matters if the sensor is getting its focus readings by the way the nozzle moves up. And nozzle position is going to be different depending on where your collar is (the collar that tightens down the screw.) Hope I could make myself clear

Just want to confirm, the HP-3655 is able to cut 18 GA Mild Steel Correct? I have seen a lot of back and forth between 16 GA, and 18 GA for this machine. Email says 16, this video shows 18.

Congrats, the first video I see someone use non mdf wood to build something like this. A good example since I don't have access to 3mm mdf to laser cut my Warhammer terrain.

WOW That's impressive- plywood even! I'll take it LOL.

Koca bir yalan. Düzgün ayarlandığında nerede ise servo gibi çalışabilir. Buna karşın oldukça ucuz bir maliyet sunar.

Funny how the company won’t tell us what laser is being used

What do you use to adhere the two parts?

How did you set it up to do that

Hello, I am trying to contact you, however i cannot get an response, could you share some contact for online support, please.

Files not available

the panel under the paper what do you call it?

Спасибо!

Where can we get these files?

May do all surface of brick? And test water absorption?😢

do you need supplier? we are Chinese CNC machine direct manufacturer. looking for cooperation with you